Run Docker Engine in swarm mode预计阅读时间: 5 分钟
When you first install and start working with Docker Engine, swarm mode is
disabled by default. When you enable swarm mode, you work with the concept of
services managed through the
docker service command.
There are two ways to run the Engine in swarm mode:
- Create a new swarm, covered in this article.
- Join an existing swarm.
When you run the Engine in swarm mode on your local machine, you can create and test services based upon images you’ve created or other available images. In your production environment, swarm mode provides a fault-tolerant platform with cluster management features to keep your services running and available.
These instructions assume you have installed the Docker Engine 1.12 or later on a machine to serve as a manager node in your swarm.
Create a swarm
When you run the command to create a swarm, the Docker Engine starts running in swarm mode.
docker swarm init
to create a single-node swarm on the current node. The Engine sets up the swarm
- switches the current node into swarm mode.
- creates a swarm named
- designates the current node as a leader manager node for the swarm.
- names the node with the machine hostname.
- configures the manager to listen on an active network interface on port 2377.
- sets the current node to
Activeavailability, meaning it can receive tasks from the scheduler.
- starts an internal distributed data store for Engines participating in the swarm to maintain a consistent view of the swarm and all services running on it.
- by default, generates a self-signed root CA for the swarm.
- by default, generates tokens for worker and manager nodes to join the swarm.
- creates an overlay network named
ingressfor publishing service ports external to the swarm.
The output for
docker swarm init provides the connection command to use when
you join new worker nodes to the swarm:
$ docker swarm init Swarm initialized: current node (dxn1zf6l61qsb1josjja83ngz) is now a manager. To add a worker to this swarm, run the following command: docker swarm join \ --token SWMTKN-1-49nj1cmql0jkz5s954yi3oex3nedyz0fb0xx14ie39trti4wxv-8vxv8rssmk743ojnwacrr2e7c \ 192.168.99.100:2377 To add a manager to this swarm, run 'docker swarm join-token manager' and follow the instructions.
Configure the advertise address
Manager nodes use an advertise address to allow other nodes in the swarm access to the Swarmkit API and overlay networking. The other nodes on the swarm must be able to access the manager node on its advertise address IP address.
If you don’t specify an advertise address, Docker checks if the system has a
single IP address. If so, Docker uses the IP address with the listening port
2377 by default. If the system has multiple IP addresses, you must specify the
--advertise-addr to enable inter-manager communication and overlay
$ docker swarm init --advertise-addr <MANAGER-IP>
You must also specify the
--advertise-addr if the address where other nodes
reach the first manager node is not the same address the manager sees as its
own. For instance, in a cloud setup that spans different regions, hosts have
both internal addresses for access within the region and external addresses that
you use for access from outside that region. In this case, specify the external
--advertise-addr so that the node can propagate that information
to other nodes that subsequently connect to it.
Refer to the
docker swarm init CLI reference
for more detail on the advertise address.
View the join command or update a swarm join token
Nodes require a secret token to join the swarm. The token for worker nodes is different from the token for manager nodes. Nodes only use the join-token at the moment they join the swarm. Rotating the join token after a node has already joined a swarm does not affect the node’s swarm membership. Token rotation ensures an old token cannot be used by any new nodes attempting to join the swarm.
To retrieve the join command including the join token for worker nodes, run:
$ docker swarm join-token worker To add a worker to this swarm, run the following command: docker swarm join \ --token SWMTKN-1-49nj1cmql0jkz5s954yi3oex3nedyz0fb0xx14ie39trti4wxv-8vxv8rssmk743ojnwacrr2e7c \ 192.168.99.100:2377 This node joined a swarm as a worker.
To view the join command and token for manager nodes, run:
$ docker swarm join-token manager To add a worker to this swarm, run the following command: docker swarm join \ --token SWMTKN-1-59egwe8qangbzbqb3ryawxzk3jn97ifahlsrw01yar60pmkr90-bdjfnkcflhooyafetgjod97sz \ 192.168.99.100:2377
--quiet flag to print only the token:
$ docker swarm join-token --quiet worker SWMTKN-1-49nj1cmql0jkz5s954yi3oex3nedyz0fb0xx14ie39trti4wxv-8vxv8rssmk743ojnwacrr2e7c
Be careful with the join tokens because they are the secrets necessary to join the swarm. In particular, checking a secret into version control is a bad practice because it would allow anyone with access to the application source code to add new nodes to the swarm. Manager tokens are especially sensitive because they allow a new manager node to join and gain control over the whole swarm.
We recommend that you rotate the join tokens in the following circumstances:
- If a token was checked-in by accident into a version control system, group chat or accidentally printed to your logs.
- If you suspect a node has been compromised.
- If you wish to guarantee that no new nodes can join the swarm.
Additionally, it is a best practice to implement a regular rotation schedule for any secret including swarm join tokens. We recommend that you rotate your tokens at least every 6 months.
swarm join-token --rotate to invalidate the old token and generate a new
token. Specify whether you want to rotate the token for
$ docker swarm join-token --rotate worker To add a worker to this swarm, run the following command: docker swarm join \ --token SWMTKN-1-2kscvs0zuymrsc9t0ocyy1rdns9dhaodvpl639j2bqx55uptag-ebmn5u927reawo27s3azntd44 \ 192.168.99.100:2377